Electric motor saegemotors

Annoncer ID: M96708
€ 995,- plus moms.
Send anmodning
Billeder
Electric motor saegemotors - købe brugte/uploadpic/tramaofinal_inserat/bilder/96708/bild1.jpg

Fabrikant

Rueetschi +Co AG, CH-5034 Suhr

Beskrivelse

3 stueck unused electric motors for Saeege machines from Rueetschi
380 / 400 Volt 50Hz Dreick circuit
5.5 KW 11.3 A
2850 rpm
With tool holder (saege leaf holder)
Shaft diameter 30mm
Diameter handle for saege leaf (middle) approx.55mm
Diameter tool holder outside approx.165mm
Total length motor approx. 570mm
Total width approx. 200mm
Price per piece
Hole distance for screwing on the motor
laengs 200mm
Hole spacing Cross 200mm
The abstinfers can be varied in the length and width,
because the motor is screwed on to the console via T-slots.
The T-slots are located on the motor.
Thus, any hole distance would be feasible via a different console.
Thread on the motor shaft is right thread (if the nut is in the
clockwise, is tightened when the motor is counterclockwise
and the mother is hooked- view from the front to the wave)
Diameter of the thread approx. 28-30mm.
direction of rotation could be possible in both directions, as the rear disc is
a groove and the front with two fitting bolts through the saege leaf with the
rear disc can be connected (not necessarily necessary).
Thus, theoretically, even with the direction of rotation, the nut can be
do not loesen.

Special price

Status

Maskine under strøm

Nej
Send anmodning

Tilbud fra:

Frank Sprengel Metallbearbeitungsmaschinen

Frank Sprengel Metallbearbeitungsmaschinen
Auf dem Holleter 55
45138 Essen

Kontaktperson: Frank Sprengel

Send anmodning
Vis telefonnummer
Tlf.: 0049 201 5067780
Vis firmaprofil



Andre interessante tilbud i denne kategori

HEIDELBERG – Dymatrix 105 CS
HEIDELBERG – Dymatrix 105 CS (BJ.2004)

Preis auf Anfrage
KOVOSVIT MAS, a.s. VO 50
KOVOSVIT MAS, a.s. VO 50

Preis auf Anfrage
VDI 40, angular tool holder, coupling DOG CLUTCH, no internal cooling
VDI 40, angular tool holder, coupling DOG CLUTCH, no internal cooling

Preis auf Anfrage
TAYLOR HOBSON Talysurf Messgerät
TAYLOR HOBSON Talysurf Messgerät

Preis auf Anfrage
2003 Mespack  H-210-D horizontal
2003 Mespack H-210-D horizontal (BJ.2003)

Preis auf Anfrage
Chiron Chiron FZ 22 L
Chiron Chiron FZ 22 L

Preis auf Anfrage
Screw Compressor Boge SF 100-2
Screw Compressor Boge SF 100-2

Preis auf Anfrage
Werkzeugschleifmaschine: DECKEL S 1
Werkzeugschleifmaschine: DECKEL S 1

Preis auf Anfrage
Roller tracks / stop systems FALKEN RB 3000x600 - Zufuhr
Roller tracks / stop systems FALKEN RB 3000x600 - Zufuhr

Preis auf Anfrage
Heidelberg Stahlfolder ET 43 A mobiler Eckfördertisch
Heidelberg Stahlfolder ET 43 A mobiler Eckfördertisch (BJ.1992)

Preis auf Anfrage
CO